Graco 313812F Instrukcja Użytkownika

313812FENOperation - MaintenanceDispensit1053-10BPatented meter and dispense system for precise one-component micro-dispensing. Not for use in explosi

Component Identification 10 313812FMetering ValveFIG. 4GREENYELLOWNEMA-23MOTORKey:A Material InletB Grounding Lug C SpoolD Metering RodE Oil Cup Retai

Setup313812F 11SetupNOTE: See Typical Installation diagram.2. 1. Perform Setup procedure for feed system compo-nents. See feed system manual(s). 2. Pl

Setup 12 313812FValve Mounting DiagramAs desired, use the following diagram to mount the metering valve. NOTE: Valve shown is for controls/motor inter

Setup313812F 13Motor Mounting DiagramIf using a non-Graco motor with the dispense valve, use the following diagram to install the non-Graco motor onto

Startup 14 313812FStartup1. Lubricate the metering rod port in the oil cup retain-ing block and fill the spool valve ports with compati-ble lubricant

Operation313812F 15OperationThe operation of the 1053 metering valve is controlled by an external source. If a Control Box was purchased, see the Cont

Pressure Relief Procedure 16 313812FPressure Relief Procedure1. Retract the metering rods. See the Control Box manual. See Related Manuals on page 2.2

Troubleshooting313812F 17TroubleshootingSchematicsFor standard machines, the schematics will be included in the Controls Parts manual. See Related Man

Rebuild 18 313812FRebuildBefore proceeding, remove material feed line and pump material out of the valve. Shut power off from control panel and discon

Rebuild313812F 19Model 1053-10B General Illustration391Metering Rod11Bottom Block21Retaining Sleeve31Screw (2)2Seal Cup12O-Ring (2)22Motor Coupling32G

Related Manuals 2 313812FContentsRelated Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Warnings . . . . . . . . . . . . . . . . .

Rebuild 20 313812FAssemblyBefore proceeding, remove any old o-rings or seals from the valve and discard, clean the valve parts with an appropriate sol

Rebuild313812F 215. Position the left Seal Plate (14) with the oil cup upwards and slide it over the Spool part of the Spool/Sleeve Assembly (7) and (

Rebuild 22 313812FMotor and Motor Coupling AssemblyDisconnect electrical power before servicing the motor and motor coupling assembly. Refer to the il

Motor and Motor Coupling Illustration313812F 23Motor and Motor Coupling IllustrationPin AlignmentRef DESCRIPTION1 MOTOR MOUNTING PLATE2 BEARING RETAIN

Electrical Requirements 24 313812FElectrical RequirementsSee Related Manuals on page 2 for valve with con-trols/motor integrated.Valve shown is with c

Technical Data313812F 25Technical DataNOTE: See feed system manuals for dimensions, weights, and wetted parts lists for those components. Dimensions,

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Warnings313812F 3WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point s

Warnings 4 313812FELECTRIC SHOCK HAZARDThis equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-tric shock.•

Isocyanate Conditions313812F 5Isocyanate Conditions Material Self-ignition Moisture Sensitivity of IsocyanatesISO will react with moisture (such as h

Grounding 6 313812FGroundingThis product must be grounded. In the event of an elec-trical short circuit, grounding reduces the risk of electric shock

Component Identification313812F 7Component IdentificationTypical System Configurations FIG. 1CONTROL POWER XX.

Component Identification 8 313812FTypical Feed System Components FIG. 2DO NOT SERVICE WITHOUTREMOVING AIR PRESSURE ANDWEARING SAFETY GLASSES.WARNINGF2

Component Identification313812F 9Typical Feed System Components (continued)FIG. 3R01284psi3022191526R01284psi30221915265 Gallon Tank with Diaphragm Pu