Graco 3A2527D Instrukcja Użytkownika

Instructions - Parts24P822 E-Flo® DC ControlModule Kit3A2527DENUser Interface for E-Flo® DC Pumps with an Advanced Motor.For professional use only.Imp

Screen MapScreen MapINITIAL SETUP(Setup Screens 5–14)SETUP AND EDIT PROFILES(Setup Screens 1–4)RUN(Run Screens 1–8)Setup Screen 5, page 22 Setup Scree

Screen MapINITIAL SETUP(Setup Screens 5–14)SETUP AND EDIT PROFILES(Setup Screens 1–4)RUN(Run Screens 1–8)SetupScreen12, page 26Setup Screen 13, page 2

Run ScreensRun ScreensThe Run screens display current target values andperformance for a selected pump and profile. Anyalarms will display in the sideb

Run ScreensRun Screen 2This screen displays pressure settings for the activepump and profile.NOTE: Some fields are grayed out, depending onsetup selecti

Run ScreensRun Screen 4This screen displays the current pressure readings oftransducers 1 and 2. Pressure can be displayed aspsi, bar, or MPa. See Set

NotesNotes3A2527D 15

Setup ScreensSetup ScreensUse the Setup screens to set controlparameters for the motor. SeeScreen Navigation and Editing, page 9 ,forinformation on ho

Setup Screens1. For systems with multiple pumps and onedisplay, select the desired pump (1 to 8), usingthe pull-down menu.Figure 15 Select Pump Number

Setup ScreensSetup Screen 2Use this screen to set the maximum, target, andminimum fluid pressure for a selected pump andprofile. In pressure mode, you w

Setup ScreensSetup Screen 3Use this screen to set your flow rate settings for aselected pump and profile. In pressure mode, youwill set a maximum flow ra

ContentsControl Module...3Installation... 3Inst

Setup ScreensSetup Screen 4Use this screen to specify how the system willrespond if the pump begins to operate outside ofthe pressure and flow settings

Setup ScreensPressure Mode Examples• Runaway Control: The user may choose to set themaximum flow toAlarm. If the flow rate exceedsthe maximum entered on

Setup ScreensSetup Screen 5Use this screen to set the lower pump size (cc) ofeach pump. The default is blank; select the correctlower size, or custom.

Setup ScreensSetup Screen 6Usethisscreentoviewthegrandtotalizervalueandset or reset the batch totalizer.Figure 28 Setup Screen 6Figure 29 Reset the To

Setup ScreensSetup Screens8 and 9Use these screens to set up the pressure transducers.The screens are identical, except Screen 8 is fortransducer 1 an

Setup ScreensSetup Screens10 and 11These screens are auto-populated by the software.Screen 10 displays the serial numbers of motors 1–4,and Screen 11

Setup ScreensSetup Screen 12Use this screen to set your modbus preferences.Figure 38 Setup Screen 12Setup Screen 12 KeyEnter the screen.For systems wi

Setup ScreensSetupScreen13Use this screen to set the desired units for pressure,totals, and flow.Figure 42 Setup Screen 13Setup Screen 13 KeySelect des

Setup ScreensSetup Screen 14Use this screen to set your date format, date, andtime.Figure 46 Setup Screen 14SetupScreen14KeyEnter the screen to set or

Setup ScreensSetupScreen15Use this screen to enter a password that will berequired to access the Setup screens. This screenalso displays the software

Control ModuleControl ModuleThe Control Module provides the interface for usersto enter selections and view information related tosetup and operation.

Error Co de TroubleshootingError Code TroubleshootingError codes can take three forms:•Alarm: alerts you to the alarm cause and shutsdown the pump.• D

Error Code T rou bleshootingDisplayCodeApplicableMotorBlinkCodeAlarm orDeviationDescriptionMND_Advanced None Advisory Maintenance counter is enabled a

PartsParts24P822 Control Module KitRefPart DescriptionQty1 24P821DISPLAY KIT, controlmodule; includesitem 1a; see manual332013 for approvalsinformatio

PartsAccessory KitsBPR Controller Kit 24V001RefPart DescriptionQty101———TRANSDUCER,miniature1102———CABLE, F/C, I.S., 8 M1103 110436GAUGE, pressure, ai

Appendix A - Modbus Variable MapAppendix A - Modbus Variable MapTo communicate through fiber optics with the E-FloDC Control Module, reference the appr

Appendix A - Modbus Variable MapNOTE: See Error Code Troubleshooting, page 30, for a description of each alarm.Table 5 Alarm Bits404112 - Pump Alarms

Appendix A - Modbus Variable Map404114 - Display Alarms Word 1Bit Event TypeEvent CodeEvent Name1 DeviationP6C_Pressure Transducer Missingothers Reser

Appendix A - Modbus Variable MapTable 7 UnitsUnit TypeSelectable UnitsUnits RegisterConverting registers tounit valuesRegister valuefor1unitPressure P

Appendix B. PumpControl from a P LCAppendix B. Pump Control from a PLCThis guide shows how to use the information inAppendix A to control a pump remot

NotesNotes3A2527D 39

InstallationInstall Optional Accessory KitsOptional accessory kits are available for purchaseseparately, including a pressure transducer kit (PN24R050

Graco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and bearing itsname to be free from def

InstallationCable ConnectionOrder an accessory cable (C) from Table 1. Connect the cable to Port 3 on the bottom of the control module(see Fig. 2). Co

OperationOperationModule ScreensThe Control Module has two sets of screens:Run and Setup. For detailed information seeRun Screens, page 12, and Setup

OperationTable 3 Module KeysMembrane KeysSoftkeysPress to toggle between Run screensand Setup screens.Enter Screen.Highlight data that can be edited.A

OperationIconsAsyoumovethrough the screens, you will notice that most information is communicated using icons ratherthan words to simplify global comm

OperationScreen Navigation and EditingRefer to this section if you have questions aboutscreen navigation or about how to enter informationand make sel