Graco SMVector - Frequency Inverter Instrukcja Użytkownika Pobierz pdf (Strona 48)

SV01M

Commissioning

Code Possible Settings

IMPORTANT

No. Name Default Selection

Sequencer: Time

units/scaling

0 0 0.1 {sec} 6553.5 Setup units/scaling for all sequencer time

related parameters

1 1 {sec} 65535

2 1 {min} 65535

NOTE:

P708 rescales the following sequencer related parameters:

- Segment Times in current step: P712, P717, P722, P727, P732, P737, P742, P747,

P752, P757, P762, P767, P772, P777, P782, P787, P792

- Sequence diagnostic/status: P561, P562

Segment #1

Frequency Setpoint

0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse

direction

Segment #1

Accel/Decel Time

20.0 0.0 {sec} 3600.0

Segment #1

Time in current step

0.0

0.0 {P708} 6553.5

0 {P708} 65535

Scaling/units depend on P708

Skip segment if time = 0

Segment #1

Digital Output State

Value set in P713 0 1 2 3 4 5 6 7

Relay (Bit 0) 0 1 0 1 0 1 0 1

TB14 (Bit 1) 0 0 1 1 0 0 1 1

I/O option Relay (Bit 2)

0 0 0 0 1 1 1 1

NOTE: P441 is the Relay Output (TB-19, 20, 21) of the

optional Digital I/O module (ESVZAL0, ESVZAL1).

bit = 0: OFF (De-energized)

bit = 1: ON (Energized)

The corresponding digital output/relay must be

set to accept data from the sequencer: P140,

P142, P441 = 27

Segment #1 TB30

Analog Output

Value

0.00 0.00 {VDC} 10.00 TB30 conﬁguration parameter must be set to

accept this value: P150 = 10

Segment #2

Frequency Setpoint

0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse

direction

Segment #2

Accel/Decel Time

20.0 0.0 {sec} 3600.0

Segment #2

Time in current step

0.0

0.0 {P708} 6553.5

0 {P708} 65535

Scaling/units depend on P708

Skip segment if time = 0

Segment #2

Digital Output State

Value set in P718 0 1 2 3 4 5 6 7

Relay (Bit 0) 0 1 0 1 0 1 0 1

TB14 (Bit 1) 0 0 1 1 0 0 1 1

I/O option Relay (Bit 2)

0 0 0 0 1 1 1 1

NOTE: P441 is the Relay Output (TB-19, 20, 21) of the

optional Digital I/O module (ESVZAL0, ESVZAL1).

bit = 0: OFF (De-energized)

bit = 1: ON (Energized)

The corresponding digital output/relay must be

set to accept data from the sequencer: P140,

P142, P441 = 27

Segment #2 TB30

Analog Output

Value

0.00 0.00 {VDC} 10.00 TB30 conﬁguration parameter must be set to

accept this value: P150 = 10

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 65 66

Komentarze do niniejszej Instrukcji

Brak uwag

Graco SMVector - Frequency Inverter Instrukcja Użytkownika Strona 48

Komentarze do niniejszej Instrukcji